The reflectance of cold rolled Aluminium during Xe-Cl excimer laser pulse irradiation with power densities in the range 10 MW/cm2 to 14 GW/cm2 has been investigated. Plasma formation at 500 MW/cm2 without previous melting at lower power is observed. "Laser cleaning" of the surface lowers plasma threshold to the pure Aluminium value and melting of the metal is detected as well between 60 and 110 MW /cm2. © 1989 SPIE
Publié suite au congrès ECASIA: 11th European Conference on Applications of Surface and Interface An...
Aluminium Kα emission (1.5 keV) produced by an 8 J, 500 ps, Nd:glass laser incident at 45° onto a la...
This work presents a new technique to remove the surface impurities from the aluminum cold-worked sh...
The reflectance of cold rolled Aluminium during Xe-Cl excimer laser pulse irradiation with power den...
The in-air treatment of large ceramic and metallic material surfaces of low roughness with high powe...
The wear properties of aluminium base alloys are relatively poor. Laser surface melting and alloying...
The role of the plasma in laser–metal interaction is of considerable interest due to its influence i...
Excimer surface treatment was conducted on 7075-T651 aluminium alloy with the aim of improving the a...
The microelectronics industry requires alumina substrates with exceptionally smooth surfaces and few...
In this paper, the influence of a laser surface treatment on the structure and properties of alumini...
International audienceSeveral phenomena are evolving at the same time in laser-induced plasmas. Mode...
Abstract. Laser irradiating process with Nd-YAG laser is investigated in order to improve the adhesi...
An excimer laser (KrF) operating at a wavelength of 248 nm was used to modify the surface microstruc...
xv, 201 leaves : ill. ; 30 cm.PolyU Library Call No.: [THS] LG51 .H577M ISE 2002 ChanAn excimer lase...
In this thesis an analysis of ultrashort pulse laser interactions with bulk aluminium and aluminium ...
Publié suite au congrès ECASIA: 11th European Conference on Applications of Surface and Interface An...
Aluminium Kα emission (1.5 keV) produced by an 8 J, 500 ps, Nd:glass laser incident at 45° onto a la...
This work presents a new technique to remove the surface impurities from the aluminum cold-worked sh...
The reflectance of cold rolled Aluminium during Xe-Cl excimer laser pulse irradiation with power den...
The in-air treatment of large ceramic and metallic material surfaces of low roughness with high powe...
The wear properties of aluminium base alloys are relatively poor. Laser surface melting and alloying...
The role of the plasma in laser–metal interaction is of considerable interest due to its influence i...
Excimer surface treatment was conducted on 7075-T651 aluminium alloy with the aim of improving the a...
The microelectronics industry requires alumina substrates with exceptionally smooth surfaces and few...
In this paper, the influence of a laser surface treatment on the structure and properties of alumini...
International audienceSeveral phenomena are evolving at the same time in laser-induced plasmas. Mode...
Abstract. Laser irradiating process with Nd-YAG laser is investigated in order to improve the adhesi...
An excimer laser (KrF) operating at a wavelength of 248 nm was used to modify the surface microstruc...
xv, 201 leaves : ill. ; 30 cm.PolyU Library Call No.: [THS] LG51 .H577M ISE 2002 ChanAn excimer lase...
In this thesis an analysis of ultrashort pulse laser interactions with bulk aluminium and aluminium ...
Publié suite au congrès ECASIA: 11th European Conference on Applications of Surface and Interface An...
Aluminium Kα emission (1.5 keV) produced by an 8 J, 500 ps, Nd:glass laser incident at 45° onto a la...
This work presents a new technique to remove the surface impurities from the aluminum cold-worked sh...
DOI
Add to ORKG