Add to ORKGThe eff ects of the Fe/Mn weight ratio (1,42 or 3,05) and cooling rate (0,1, 0,2, 0,5, or 0,6 °C/s) on the area fraction of α-AlFeSi and β-AlFeSi intermetallic compounds in Al-7.5Si-3.75Cu-0.5Mg-0.55Fe-xMn aluminum alloy were studied. It was found that the diff erence between the formation temperature of the β-AlFeSi phase and the formation tem-perature of the eutectic Al-Si may determine the possibilities of β-AlFeSi elimination/reduction by increasing the cooling rate
The cooling rate is one of the main tools available to the process engineer by means of which it is ...
International audienceThe transformation of primary eutectic Al-6(Mn,Fe) intermetallics into alpha-A...
The present paper reports the formation of novel morphologies of intermetallic compounds during the ...
The effects of the Fe/Mn weight ratio (1,42 or 3,05) and cooling rate (0,1, 0,2, 0,5, or 0,6 °C/s) o...
Secondary Al–Si alloys Al7.1Si(1.5-xMn)Fe(xMn)Mn with xMn = 0, 0.3, 0.375, 0.6, 0.75 at.% have been ...
Aluminum-Silicon (Al-Si) alloys are one of the most versatile aluminum alloys. Iron is considered on...
In AA2618 aluminum alloy, the iron- and nickel-rich intermetallics formed during solidification are ...
The influence of cooling rate during solidification on the three dimensional (3D) morphology of iron...
Mn was an important alloying element used in Al–Mg–Mn alloys. However, it had to be limited to a low...
The formation of iron-bearing intermetallics in the 413 type of aluminum alloys was investigated com...
In this work, an analysis of the solidification course of the AlFeMnSi alloys was carried out in the...
In Al-Si alloy the iron is the most common impurity and with presence of other elements in alloy cre...
The aluminum alloys corresponding to the 6000 series are mainly manufactured by mechanical forming p...
© The Author(s) 2018. Iron (Fe) is the most common and the most detrimental impurity element in Al a...
Post-eutectic reactions occurring in Al-Si hypoeutectic alloys containing different proportions of C...
The cooling rate is one of the main tools available to the process engineer by means of which it is ...
International audienceThe transformation of primary eutectic Al-6(Mn,Fe) intermetallics into alpha-A...
The present paper reports the formation of novel morphologies of intermetallic compounds during the ...
The effects of the Fe/Mn weight ratio (1,42 or 3,05) and cooling rate (0,1, 0,2, 0,5, or 0,6 °C/s) o...
Secondary Al–Si alloys Al7.1Si(1.5-xMn)Fe(xMn)Mn with xMn = 0, 0.3, 0.375, 0.6, 0.75 at.% have been ...
Aluminum-Silicon (Al-Si) alloys are one of the most versatile aluminum alloys. Iron is considered on...
In AA2618 aluminum alloy, the iron- and nickel-rich intermetallics formed during solidification are ...
The influence of cooling rate during solidification on the three dimensional (3D) morphology of iron...
Mn was an important alloying element used in Al–Mg–Mn alloys. However, it had to be limited to a low...
The formation of iron-bearing intermetallics in the 413 type of aluminum alloys was investigated com...
In this work, an analysis of the solidification course of the AlFeMnSi alloys was carried out in the...
In Al-Si alloy the iron is the most common impurity and with presence of other elements in alloy cre...
The aluminum alloys corresponding to the 6000 series are mainly manufactured by mechanical forming p...
© The Author(s) 2018. Iron (Fe) is the most common and the most detrimental impurity element in Al a...
Post-eutectic reactions occurring in Al-Si hypoeutectic alloys containing different proportions of C...
The cooling rate is one of the main tools available to the process engineer by means of which it is ...
International audienceThe transformation of primary eutectic Al-6(Mn,Fe) intermetallics into alpha-A...
The present paper reports the formation of novel morphologies of intermetallic compounds during the ...