Combustion improvement and pollutants reduction with diesel-gasoline blends by means of a highly tunable laser plasma induced ignition system

[EN] The use of alternative fuels in compression ignition engines, either completely or partially replacing the conventional ones, have potential to reduce pollutant emissions (especially soot). However, some of these fuels do not provide good ignition features under diesel engine like conditions, which affects engine efficiency. Thus, in order to extend the application of alternative fuels, the current research proposes the use of a laser induced plasma ignition system to assist on the combustion of blends of fuels with less reactivity than pure diesel. This fuel has been chosen as the base component and it has been mixed with gasoline (as the low-reactivity fuel) in different ratios as an example of fuels with very different reactivity properties. Tests have been performed in a single cylinder optically accessible engine, allowing deeper study of combustion development and soot formation. For different in-cylinder conditions and fuel blends, the effect of laser induced plasma ignition system has been evaluated at different crank angle degrees and locations inside the combustion chamber. The application of these blends under low-reactivity engine conditions show that combustion efficiency is dramatically affected. However, the study proves that it is possible to control blend ignition delay and flame lift-off length by means of laser induced plasma. Besides, using the proper ignition system configuration, combustion characteristics similar to those of diesel fuel autoignition can be achieved for high gasoline substitution rates. They lead to similar energy release rates, which confirms that diesel-gasoline blends can reach a combustion efficiency close to pure diesel, while a strong reduction on soot formation was also obtained. These results open a door to efficiency improvement and pollutant reduction by means of a highly tunable ignition of alternative fuel blends.The authors acknowledge that this research work has been partly funded by the Government of Spain and FEDER under TRANCO project (TRA2017-87694-R).Pastor, JV.; García-Oliver, JM.; García Martínez, A.; Mico Reche, C. (2020). Combustion improvement and pollutants reduction with diesel-gasoline blends by means of a highly tunable laser plasma induced ignition system. Journal of Cleaner Production. 271:1-13. https://doi.org/10.1016/j.jclepro.2020.122499113271Ahmed, W., & Sarkar, B. (2018). Impact of carbon emissions in a sustainable supply chain management for a second generation biofuel. Journal of Cleaner Production, 186, 807-820. doi:10.1016/j.jclepro.2018.02.289Bae, C., & Kim, J. (2017). Alternative fuels for internal combustion engines. Proceedings of the Combustion Institute, 36(3), 3389-3413. doi:10.1016/j.proci.2016.09.009Bakker, P. C., Maes, N., & Dam, N. (2017). The potential of on- and off-resonant formaldehyde imaging combined with bootstrapping in diesel sprays. Combustion and Flame, 182, 20-27. doi:10.1016/j.combustflame.2017.03.032Barrientos, E. J., Lapuerta, M., & Boehman, A. L. (2013). Group additivity in soot formation for the example of C-5 oxygenated hydrocarbon fuels. Combustion and Flame, 160(8), 1484-1498. doi:10.1016/j.combustflame.2013.02.024Benajes, J., García, A., Domenech, V., & Durrett, R. (2013). An investigation of partially premixed compression ignition combustion using gasoline and spark assistance. Applied Thermal Engineering, 52(2), 468-477. doi:10.1016/j.applthermaleng.2012.12.025Benajes, J., García, A., Monsalve-Serrano, J., & Boronat, V. (2017). Achieving clean and efficient engine operation up to full load by combining optimized RCCI and dual-fuel diesel-gasoline combustion strategies. Energy Conversion and Management, 136, 142-151. doi:10.1016/j.enconman.2017.01.010Bermúdez, V., García, J. M., Juliá, E., & Martínez, S. (2003). Engine with Optically Accessible Cylinder Head: A Research Tool for Injection and Combustion Processes. SAE Technical Paper Series. doi:10.4271/2003-01-1110Dale, J. D., Smy, P. R., & Clements, R. M. (1978). Laser Ignited Internal Combustion Engine - An Experimental Study. SAE Technical Paper Series. doi:10.4271/780329Gómez, A., García-Contreras, R., Soriano, J. A., & Mata, C. (2020). Comparative study of the opacity tendency of alternative diesel fuels blended with gasoline. Fuel, 264, 116860. doi:10.1016/j.fuel.2019.116860Han, D., Wang, C., Duan, Y., Tian, Z., & Huang, Z. (2014). An experimental study of injection and spray characteristics of diesel and gasoline blends on a common rail injection system. Energy, 75, 513-519. doi:10.1016/j.energy.2014.08.006Higgins, B., & Siebers, D. L. (2001). Measurement of the Flame Lift-Off Location on DI Diesel Sprays Using OH Chemiluminescence. SAE Technical Paper Series. doi:10.4271/2001-01-0918Hossain, A. K., & Davies, P. A. (2010). Plant oils as fuels for compression ignition engines: A technical review and life-cycle analysis. Renewable Energy, 35(1), 1-13. doi:10.1016/j.renene.2009.05.009Hu, Y., Wang, Z., & Li, X. (2020). Impact of policies on electric vehicle diffusion: An evolutionary game of small world network analysis. Journal of Cleaner Production, 265, 121703. doi:10.1016/j.jclepro.2020.121703Hwang, J., Kim, W., Bae, C., Choe, W., Cha, J., & Woo, S. (2017). Application of a novel microwave-assisted plasma ignition system in a direct injection gasoline engine. Applied Energy, 205, 562-576. doi:10.1016/j.apenergy.2017.07.129Kim, H., & Choi, B. (2008). Effect of ethanol–diesel blend fuels on emission and particle size distribution in a common-rail direct injection diesel engine with warm-up catalytic converter. Renewable Energy, 33(10), 2222-2228. doi:10.1016/j.renene.2008.01.002König, A., Ulonska, K., Mitsos, A., & Viell, J. (2019). Optimal Applications and Combinations of Renewable Fuel Production from Biomass and Electricity. Energy & Fuels, 33(2), 1659-1672. doi:10.1021/acs.energyfuels.8b03790Kumar, S., Cho, J. H., Park, J., & Moon, I. (2013). Advances in diesel–alcohol blends and their effects on the performance and emissions of diesel engines. Renewable and Sustainable Energy Reviews, 22, 46-72. doi:10.1016/j.rser.2013.01.017Liu, F., Gao, Y., Wu, H., Zhang, Z., He, X., & Li, X. (2018). Investigation on Soot Characteristics of Gasoline/Diesel Blends in a Laminar Coflow Diffusion Flame. Energy & Fuels, 32(7), 7841-7850. doi:10.1021/acs.energyfuels.7b04051Medeiros, D. L., Sales, E. A., & Kiperstok, A. (2015). Energy production from microalgae biomass: carbon footprint and energy balance. Journal of Cleaner Production, 96, 493-500. doi:10.1016/j.jclepro.2014.07.038Miller Jothi, N. K., Nagarajan, G., & Renganarayanan, S. (2007). Experimental studies on homogeneous charge CI engine fueled with LPG using DEE as an ignition enhancer. Renewable Energy, 32(9), 1581-1593. doi:10.1016/j.renene.2006.08.007Omari, A., Heuser, B., & Pischinger, S. (2017). Potential of oxymethylenether-diesel blends for ultra-low emission engines. Fuel, 209, 232-237. doi:10.1016/j.fuel.2017.07.107Pastor, J., Garcia-Oliver, J. M., Garcia, A., & Nareddy, V. R. (2017). Characterization of Spray Evaporation and Mixing Using Blends of Commercial Gasoline and Diesel Fuels in Engine-Like Conditions. SAE Technical Paper Series. doi:10.4271/2017-01-0843PASTOR, J., JAVIERLOPEZ, J., GARCIA, J., & PASTOR, J. (2008). A 1D model for the description of mixing-controlled inert diesel sprays. Fuel, 87(13-14), 2871-2885. doi:10.1016/j.fuel.2008.04.017Pastor, J. V., Garcia-Oliver, J. M., Novella, R., & Xuan, T. (2015). Soot Quantification of Single-Hole Diesel Sprays by Means of Extinction Imaging. SAE International Journal of Engines, 8(5), 2068-2077. doi:10.4271/2015-24-2417Pastor, J. V., García, A., Micó, C., & Lewiski, F. (2020). An optical investigation of Fischer-Tropsch diesel and Oxymethylene dimethyl ether impact on combustion process for CI engines. Applied Energy, 260, 114238. doi:10.1016/j.apenergy.2019.114238Pastor, J. V., García-Oliver, J. M., García, A., Micó, C., & Durrett, R. (2013). A spectroscopy study of gasoline partially premixed compression ignition spark assisted combustion. Applied Energy, 104, 568-575. doi:10.1016/j.apenergy.2012.11.030Pastor, J. V., García-Oliver, J. M., García, A., Micó, C., & Möller, S. (2016). Application of optical diagnostics to the quantification of soot in n-alkane flames under diesel conditions. Combustion and Flame, 164, 212-223. doi:10.1016/j.combustflame.2015.11.018Pastor, J. V., García-Oliver, J. M., García, A., & Pinotti, M. (2017). Effect of laser induced plasma ignition timing and location on Diesel spray combustion. Energy Conversion and Management, 133, 41-55. doi:10.1016/j.enconman.2016.11.054Pastor, J. V., García-Oliver, J. M., García, A., & Pinotti, M. (2016). Laser induced plasma methodology for ignition control in direct injection sprays. Energy Conversion and Management, 120, 144-156. doi:10.1016/j.enconman.2016.04.086Pastor, J. V., Garcia-Oliver, J. M., Pastor, J. M., & Vera-Tudela, W. (2015). ONE-DIMENSIONAL DIESEL SPRAY MODELING OF MULTICOMPONENT FUELS. Atomization and Sprays, 25(6), 485-517. doi:10.1615/atomizspr.2014010370Pastor, J. V., García, A., Micó, C., & García-Carrero, A. A. (2020). Experimental study of influence of Liquefied Petroleum Gas addition in Hydrotreated Vegetable Oil fuel on ignition delay, flame lift off length and soot emission under diesel-like conditions. Fuel, 260, 116377. doi:10.1016/j.fuel.2019.116377Phuoc, T. X. (2006). Laser-induced spark ignition fundamental and applications. Optics and Lasers in Engineering, 44(5), 351-397. doi:10.1016/j.optlaseng.2005.03.008Pickett, L. M., & Siebers, D. L. (2004). Soot in diesel fuel jets: effects of ambient temperature, ambient density, and injection pressure. Combustion and Flame, 138(1-2), 114-135. doi:10.1016/j.combustflame.2004.04.006Rajak, U., Nashine, P., & Verma, T. N. (2020). Effect of spirulina microalgae biodiesel enriched with diesel fuel on performance and emission characteristics of CI engine. Fuel, 268, 117305. doi:10.1016/j.fuel.2020.117305Sequino, L., Mancaruso, E., Monsalve-Serrano, J., & Garcia, A. (2020). Infrared/Visible Optical Diagnostics of RCCI Combustion with Dieseline in a Compression Ignition Engine. SAE Technical Paper Series. doi:10.4271/2020-01-0557Vu, D. N., Das, S. K., Jwa, K., & Lim, O. (2018). Characteristics of auto-ignition in gasoline–biodiesel blended fuel under engine-like conditions. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 233(5), 1352-1364. doi:10.1177/0954407018763194Wang, C., Wood, J., Wang, Y., Geng, X., & Long, X. (2020). CO2 emission in transportation sector across 51 countries along the Belt and Road from 2000 to 2014. Journal of Cleaner Production, 266, 122000. doi:10.1016/j.jclepro.2020.122000Wang, J., Yang, F., & Ouyang, M. (2015). Dieseline fueled flexible fuel compression ignition engine control based on in-cylinder pressure sensor. Applied Energy, 159, 87-96. doi:10.1016/j.apenergy.2015.08.101Weinrotter, M., Wintner, E., Iskra, K., Neger, T., Olofsson, J., Seyfried, H., … Johansson, B. (2005). Optical Diagnostics of Laser-Induced and Spark Plug-Assisted HCCI Combustion. SAE Technical Paper Series. doi:10.4271/2005-01-0129Westlye, F. R., Penney, K., Ivarsson, A., Pickett, L. M., Manin, J., & Skeen, S. A. (2017). Diffuse back-illumination setup for high temporally resolved extinction imaging. Applied Optics, 56(17), 5028. doi:10.1364/ao.56.005028Xuan, T., Desantes, J. M., Pastor, J. V., & Garcia-Oliver, J. M. (2019). Soot temperature characterization of spray a flames by combined extinction and radiation methodology. Combustion and Flame, 204, 290-303. doi:10.1016/j.combustflame.2019.03.023Xuan, T., Pastor, J. V., García-Oliver, J. M., García, A., He, Z., Wang, Q., & Reyes, M. (2019). In-flame soot quantification of diesel sprays under sooting/non-sooting critical conditions in an optical engine. Applied Thermal Engineering, 149, 1-10. doi:10.1016/j.applthermaleng.2018.11.112Yan, X., Corbin, K. R., Burton, R. A., & Tan, D. K. Y. (2020). Agave: A promising feedstock for biofuels in the water-energy-food-environment (WEFE) nexus. Journal of Cleaner Production, 261, 121283. doi:10.1016/j.jclepro.2020.121283Yilmaz, N., Vigil, F. M., Burl Donaldson, A., & Darabseh, T. (2014). Investigation of CI engine emissions in biodiesel–ethanol–diesel blends as a function of ethanol concentration. Fuel, 115, 790-793. doi:10.1016/j.fuel.2013.08.012Zheng, L., Ma, X., Wang, Z., & Wang, J. (2015). An optical study on liquid-phase penetration, flame lift-off location and soot volume fraction distribution of gasoline–diesel blends in a constant volume vessel. Fuel, 139, 365-373. doi:10.1016/j.fuel.2014.09.00