Two finger technique only. This flute was made on the spot froma pawpaw stalk. 13" flute, end blown out of the side of the mouth, two finger holes and stopped at the end. Second tune was overblown to get an octave higher. The flute was cut to shape with a pocket knife, the two holes being cut and then shapped with a piece of stick. The other (mouth) end was reduced to lenght until the finger hole notes sounded correct. Flute tunes with Umstshingozi end blown transverse flute
Includes abstract.Includes bibliographical references.The first flutes were made in prehistoric time...
Indigenous folk flute tune instrumental, with an unaccompanied nyamulera (four-holed, V-notched indi...
Here, Maria Tadeu is making the purikai flute. The purikai, is a longitudinal flute with four holes...
Two finger technique only. This flute was made on the spot froma pawpaw stalk. 13" flute, end blown ...
Two finger technique only. This flute was made on the spot froma pawpaw stalk. 13" flute, end blown ...
Two finger technique only. This flute was made on the spot froma pawpaw stalk. 13" flute, end blown ...
This flute is unusual in that it is made from a single section of banboo 28 inches long by 3/4 inche...
This flute is unusual in that it is made from a single section of banboo 28 inches long by 3/4 inche...
The flute (Omubanda. s. Emibanda. pl.) is a notched flute, end blown onto a V shaped notch cut into ...
The flute blower kept his right ear covered with his hand whilst he played. He also sang voiced note...
Flute has ten holes for playing.https://scholarworks.umt.edu/mansfieldartifacts/1036/thumbnail.jp
Double tounging is one of playing techniques on the flute which emphasizes on the use of a double to...
Timoti wet the flute with water first before playing. These flutes, they say, are played in January ...
The flute was 6 feet long, and was made of the section of an old bicycle pump. Walking song. (Also s...
In assessing the steps in the evolution in the construction of the vertical flute, the most importan...
Includes abstract.Includes bibliographical references.The first flutes were made in prehistoric time...
Indigenous folk flute tune instrumental, with an unaccompanied nyamulera (four-holed, V-notched indi...
Here, Maria Tadeu is making the purikai flute. The purikai, is a longitudinal flute with four holes...
Two finger technique only. This flute was made on the spot froma pawpaw stalk. 13" flute, end blown ...
Two finger technique only. This flute was made on the spot froma pawpaw stalk. 13" flute, end blown ...
Two finger technique only. This flute was made on the spot froma pawpaw stalk. 13" flute, end blown ...
This flute is unusual in that it is made from a single section of banboo 28 inches long by 3/4 inche...
This flute is unusual in that it is made from a single section of banboo 28 inches long by 3/4 inche...
The flute (Omubanda. s. Emibanda. pl.) is a notched flute, end blown onto a V shaped notch cut into ...
The flute blower kept his right ear covered with his hand whilst he played. He also sang voiced note...
Flute has ten holes for playing.https://scholarworks.umt.edu/mansfieldartifacts/1036/thumbnail.jp
Double tounging is one of playing techniques on the flute which emphasizes on the use of a double to...
Timoti wet the flute with water first before playing. These flutes, they say, are played in January ...
The flute was 6 feet long, and was made of the section of an old bicycle pump. Walking song. (Also s...
In assessing the steps in the evolution in the construction of the vertical flute, the most importan...
Includes abstract.Includes bibliographical references.The first flutes were made in prehistoric time...
Indigenous folk flute tune instrumental, with an unaccompanied nyamulera (four-holed, V-notched indi...
Here, Maria Tadeu is making the purikai flute. The purikai, is a longitudinal flute with four holes...