The mechanical and structural properties were studied at room temperature for Al-2wt.%Ag and Al-2wt.%Ag-1wt.%Sn alloys 503 K–583 K. The variation in the internal friction, Q−1, dynamic Young's modulus, Y, Vickers hardness, Hv, and X-ray diffraction patterns were obtained. For 533 K the internal friction showed abrupt increase while Young's modulus and Vickers hardness showed minima. The results showed a remarkable dependence of the measured parameters on both Sn addition and the heat treatment regime
Regularities of the influence of microheterogeneity and crystallization conditions of the Al-50 wt %...
Al–Sn-based alloy was produced using the accumulative roll bonding (ARB) process followed by heat tr...
Variations of the Young's modulus and of the internal friction during the aging of the supersaturate...
The mechanical and structural properties were studied at room temperature for Al-2wt.%Ag and Al-2wt...
Al-Sn alloys have a very long history to be used as bearing materials. These alloys provide a good c...
Aluminum alloys, which have been widely used in various manufacturing industries as an upper layer o...
The nanoindentation method was used to measure the Young's modulus and hardness of the phases of the...
The mechanical properties of a typical sintered aluminium alloy (Al-4.4Cu-0.8Si-0.5Mg) have been imp...
The microstructures and tensile properties of the as-cast and heat treated Mg-7Zn-5Al based alloys w...
Structure, wetting, mechanical and electrical transport properties of tin- (2.5, 3.5, 5 and 10) wt....
The effects of Sn addition (0, 0.5, 1.0, 2.0 and 3 wt%) on microstructure of Mg-4Zn-1.5Al alloy in c...
The effects of nickel and nickel combined tin additions on mechanical properties and microstructural...
Microstructure and thermal properties of slowly cooled Sn–10% Ag and Sn–20% Ag alloys were experimen...
In this paper, the results from studies regarding near-eutectic Al-Si alloys with Sn as an alloying ...
The structural, surface and transport properties of Sn-Ag alloys were investigated by X-ray diffract...
Regularities of the influence of microheterogeneity and crystallization conditions of the Al-50 wt %...
Al–Sn-based alloy was produced using the accumulative roll bonding (ARB) process followed by heat tr...
Variations of the Young's modulus and of the internal friction during the aging of the supersaturate...
The mechanical and structural properties were studied at room temperature for Al-2wt.%Ag and Al-2wt...
Al-Sn alloys have a very long history to be used as bearing materials. These alloys provide a good c...
Aluminum alloys, which have been widely used in various manufacturing industries as an upper layer o...
The nanoindentation method was used to measure the Young's modulus and hardness of the phases of the...
The mechanical properties of a typical sintered aluminium alloy (Al-4.4Cu-0.8Si-0.5Mg) have been imp...
The microstructures and tensile properties of the as-cast and heat treated Mg-7Zn-5Al based alloys w...
Structure, wetting, mechanical and electrical transport properties of tin- (2.5, 3.5, 5 and 10) wt....
The effects of Sn addition (0, 0.5, 1.0, 2.0 and 3 wt%) on microstructure of Mg-4Zn-1.5Al alloy in c...
The effects of nickel and nickel combined tin additions on mechanical properties and microstructural...
Microstructure and thermal properties of slowly cooled Sn–10% Ag and Sn–20% Ag alloys were experimen...
In this paper, the results from studies regarding near-eutectic Al-Si alloys with Sn as an alloying ...
The structural, surface and transport properties of Sn-Ag alloys were investigated by X-ray diffract...
Regularities of the influence of microheterogeneity and crystallization conditions of the Al-50 wt %...
Al–Sn-based alloy was produced using the accumulative roll bonding (ARB) process followed by heat tr...
Variations of the Young's modulus and of the internal friction during the aging of the supersaturate...