Based on the features of diode-pumped Yb3+:Y2SiO5 (Yb:YSO) lasers, a thermal model was established. According to the latest reports and measurements on thermal parameters, and further considering the heat transfer on side surface, thermal lensing effect of Yb:YSO was studied for the first time to our knowledge. Under the pump power of 17 W, the maximum temperature (488.4 °C) and the maximum distortion (1.24 μm) were obtained by solving Poisson equation using finite difference method. Moreover, thermal lens focal length was measured through a plane-plane cavity. All the results demonstrate that the theoretical result will be closer to the reality if we take the heat transfer on side surfaces into account
The aims of the research is to study the thermal lensing induced by end-pumped 1.5 at % Nd:YVO4 Lase...
Theoretical and experimental results are reported on the thermal lensing effect caused by the radial...
The most difficult challenge in the design of such high-power end-pumped lasers is the handling of t...
Based on the features of diode-pumped Yb3+:Y2SiO5 (Yb:YSO) lasers, a thermal model was established...
A Shack–Hartmann wavefront sensor was used to measure thermal lensing in diode-end-pumped Yb-doped G...
The end-pumped solid-state laser is a mature design architecture exploited for many scientific, indu...
In this thesis, analysis of thermal effects and various approaches for their mitigation in diode end...
The induced lenses in the Yb:YAG rods and disks end-pumped by a Gaussian beam were analyzed both ana...
In this thesis, analysis of thermal effects and various approaches for their mitigation in diode end...
The induced lenses in the Yb:YAG rods and disks end-pumped by a Gaussian beam were analyzed both ana...
We present realistic calculations of thermal lensing in edge-pumped, Yb3+ doped yttrium aluminum gar...
One of the major limitations of scaling diode-end-pumped solid-state lasers to high powers is introd...
We measured the thermal distortion induced on an optical probe beam passing through a diode-end-pump...
We present realistic calculations of thermal lensing in edge-pumped, Yb3+ doped yttrium aluminum gar...
We present realistic calculations of thermal lensing in edge-pumped, Yb3+ doped yttrium aluminum gar...
The aims of the research is to study the thermal lensing induced by end-pumped 1.5 at % Nd:YVO4 Lase...
Theoretical and experimental results are reported on the thermal lensing effect caused by the radial...
The most difficult challenge in the design of such high-power end-pumped lasers is the handling of t...
Based on the features of diode-pumped Yb3+:Y2SiO5 (Yb:YSO) lasers, a thermal model was established...
A Shack–Hartmann wavefront sensor was used to measure thermal lensing in diode-end-pumped Yb-doped G...
The end-pumped solid-state laser is a mature design architecture exploited for many scientific, indu...
In this thesis, analysis of thermal effects and various approaches for their mitigation in diode end...
The induced lenses in the Yb:YAG rods and disks end-pumped by a Gaussian beam were analyzed both ana...
In this thesis, analysis of thermal effects and various approaches for their mitigation in diode end...
The induced lenses in the Yb:YAG rods and disks end-pumped by a Gaussian beam were analyzed both ana...
We present realistic calculations of thermal lensing in edge-pumped, Yb3+ doped yttrium aluminum gar...
One of the major limitations of scaling diode-end-pumped solid-state lasers to high powers is introd...
We measured the thermal distortion induced on an optical probe beam passing through a diode-end-pump...
We present realistic calculations of thermal lensing in edge-pumped, Yb3+ doped yttrium aluminum gar...
We present realistic calculations of thermal lensing in edge-pumped, Yb3+ doped yttrium aluminum gar...
The aims of the research is to study the thermal lensing induced by end-pumped 1.5 at % Nd:YVO4 Lase...
Theoretical and experimental results are reported on the thermal lensing effect caused by the radial...
The most difficult challenge in the design of such high-power end-pumped lasers is the handling of t...