Add to ORKG© 2015, Allerton Press, Inc. In the present work, we report the results of tribological studies on commercially pure copper (Cu 99.9%) in contact a with graphitic material. The samples under study were made with two types of micro-structures, i.e., a coarse-grained (CG) microstructure with an average grain size of 20–60 μm after annealing and a submicrocrystalline (SMC) microstructure with an average grain size of 0.22 μm after severe plastic deformation (SPD) processing through equal-channel angular pressing (ECAP) via the Conform scheme. It has been shown that the SMC samples after ECAP-Conform processing reveal friction coefficients 12–20% lower than in the case of the annealed coarse-grained (CG) sample
2-s2.0-84905833741 - ScopusIn this study, the tribological behavior of copper coatings was investiga...
Using lightweight systems and friction reduction approaches are two main contributors towards modern...
Tailoring the surface properties of a material for low friction and little wear has long been a goal...
© 2015, Allerton Press, Inc. In the present work, we report the results of tribological studies on c...
Dry sliding tribological behavior of an electro-deposited nanocrystalline Cu (nc Cu) and a conventio...
The tribological behavior of copper was studied with a pin-on-disk system designed to achieve a wide...
Copper–graphite composites with 0–4 wt % graphite were fabricated by field-assisted hot ...
International audienceDurability of engineering workpieces surfaces is well-known to be strongly rel...
Focus of the study has been placed on the effect of graphite content on tribological behavior of a C...
Two copper based composites: an experimental Cu-Al2O3 and commercial GlidCop AL-60 grade (with 1.1 w...
This work analyses the effect of annealing conditions on tribolayer formation in copper under dry sl...
Pure Cu of 99.98 wt.% purity has been processed at room temperature by diverse techniques of severe ...
Mechanical and microstructural analysis of equal channel angular pressed copper was experimentally i...
Abstract: The equal channel angular pressing (ECAP) technique is now recognised for achieving very s...
The article of record as published may be found at http://dx.doi.org/10.1007/s10853-008-2714-yThe mi...
2-s2.0-84905833741 - ScopusIn this study, the tribological behavior of copper coatings was investiga...
Using lightweight systems and friction reduction approaches are two main contributors towards modern...
Tailoring the surface properties of a material for low friction and little wear has long been a goal...
© 2015, Allerton Press, Inc. In the present work, we report the results of tribological studies on c...
Dry sliding tribological behavior of an electro-deposited nanocrystalline Cu (nc Cu) and a conventio...
The tribological behavior of copper was studied with a pin-on-disk system designed to achieve a wide...
Copper–graphite composites with 0–4 wt % graphite were fabricated by field-assisted hot ...
International audienceDurability of engineering workpieces surfaces is well-known to be strongly rel...
Focus of the study has been placed on the effect of graphite content on tribological behavior of a C...
Two copper based composites: an experimental Cu-Al2O3 and commercial GlidCop AL-60 grade (with 1.1 w...
This work analyses the effect of annealing conditions on tribolayer formation in copper under dry sl...
Pure Cu of 99.98 wt.% purity has been processed at room temperature by diverse techniques of severe ...
Mechanical and microstructural analysis of equal channel angular pressed copper was experimentally i...
Abstract: The equal channel angular pressing (ECAP) technique is now recognised for achieving very s...
The article of record as published may be found at http://dx.doi.org/10.1007/s10853-008-2714-yThe mi...
2-s2.0-84905833741 - ScopusIn this study, the tribological behavior of copper coatings was investiga...
Using lightweight systems and friction reduction approaches are two main contributors towards modern...
Tailoring the surface properties of a material for low friction and little wear has long been a goal...