There is a considerable current interest in learning how to process genuinely nanostructured ceramics as they offer the potential for significantly enhanced properties; however, it is often difficult to make large enough components to allow more than the most basic of property measurements. In this work, densified components measuring up to 50 mm in size have been produced and a number of very interesting properties have been measured and demonstrated
The deformation strain rate of nanocrystalline Y-TZP shows an increase by a factor 4 if the grain si...
Large scale 50 × 50 mm sintered nanostructured zirconia ceramics were fabricated via industrially vi...
Zirconia samples doped with 3 mol% yttria were prepared by gel precipitation from a metal chloride s...
The term nanoceramics is well known in the ceramic field for at least two decades. Even though there...
Conventional ceramic forming routes have been adapted for the processing of ~16 nm, 3 mol% yttria st...
A new colloidal route leading to the production of ~99% dense 3 mol% yttria stabilized zirconia nano...
The processing of ceramic nanopowders into components has been investigated via a series of research...
When used in prosthetic dentistry, zirconia encounters severe durability issues due to low temperatu...
In the current paper we present a study of the sinterability of two zirconia (ZrO2) nanopowders with...
In the current paper we present a study of the sinterability of two zirconia (ZrO2) nanopowders with...
A study has been conducted on the pressure-less sintering of the ZrC>2- Y2O3 system that contains 3 ...
The sintering of nanosize powders of fully stabilized zirconia was investigated using the spark plas...
For the production of nanostructured ceramics of yttria-zirconia four powders differing in agglomera...
3 mol% Y2O3-stabilized zirconia nanopowders were fabricated using various sintering techniques; conv...
Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Materials Science and Engineering, ...
The deformation strain rate of nanocrystalline Y-TZP shows an increase by a factor 4 if the grain si...
Large scale 50 × 50 mm sintered nanostructured zirconia ceramics were fabricated via industrially vi...
Zirconia samples doped with 3 mol% yttria were prepared by gel precipitation from a metal chloride s...
The term nanoceramics is well known in the ceramic field for at least two decades. Even though there...
Conventional ceramic forming routes have been adapted for the processing of ~16 nm, 3 mol% yttria st...
A new colloidal route leading to the production of ~99% dense 3 mol% yttria stabilized zirconia nano...
The processing of ceramic nanopowders into components has been investigated via a series of research...
When used in prosthetic dentistry, zirconia encounters severe durability issues due to low temperatu...
In the current paper we present a study of the sinterability of two zirconia (ZrO2) nanopowders with...
In the current paper we present a study of the sinterability of two zirconia (ZrO2) nanopowders with...
A study has been conducted on the pressure-less sintering of the ZrC>2- Y2O3 system that contains 3 ...
The sintering of nanosize powders of fully stabilized zirconia was investigated using the spark plas...
For the production of nanostructured ceramics of yttria-zirconia four powders differing in agglomera...
3 mol% Y2O3-stabilized zirconia nanopowders were fabricated using various sintering techniques; conv...
Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Materials Science and Engineering, ...
The deformation strain rate of nanocrystalline Y-TZP shows an increase by a factor 4 if the grain si...
Large scale 50 × 50 mm sintered nanostructured zirconia ceramics were fabricated via industrially vi...
Zirconia samples doped with 3 mol% yttria were prepared by gel precipitation from a metal chloride s...