The oxygen pressure over solid molybdenum dioxide in equilibrium with liquid molybdenum oxide was determined by transpiration and solid electrolytic galvanic cell methods at 950ºC and 900º, 950º and 1000ºC respectively. The results were compared to those expected from thermodynamic data on the Mo-O system. Possible reactions between MoO₂ and SiO₂ were studied at different oxygen pressures up to 1550ºC. No compound formation or solid solution between MoO₂ and SiO₂ was detected by x-ray diffraction techniques. The phase boundary between MoO₂ and liquid molybdenum oxide was checked by microscopic examination of quenched samples. Equilibration runs were carried out in silica and platinum capsules --Abstract, page ii
DTFH61-85-C-00149The U.S. Accelerated Loading Facility (ALF), a full-scale accelerated pavement test...
During this experimental testing program the effects of the simultaneous application of high pressur...
Paper 1: “Surface electromagnetic wave (SEW) dispersion curves are usually calculated using a simple...
At present copper sulfide ores are recovered by pyrometallurgical processes. While the recovery of c...
Shell molds containing additions of ten to fifty percent magnetite, Fe3O4, of various particle sizes...
The flotation of sulphide minerals from siliceous and calcareous gangue minerals always gives a conc...
For many years, there has been talk expressing great concern about the oil reserves in the United St...
The effect of the area and type of surface of ten silica thickeners and aluminum oxide on grease per...
Presently, the theory is held that the total frog skin potential (P.D.) is generated within the epid...
The ability of silica to carry a load to within a few degrees of its melting point and its tolerance...
The vapor phase photolysis of benzoic acid has been investigated in a flow system at temperatures ra...
Not Available.J. Carter EaveyNot ListedNot ListedMaster of ArtsDepartment Not ListedCunningham Memor...
With the advent of legislation against pollution, and rising wage, manufacturing, and materials cost...
Reaction of aqueous solutions of either lanthanum or cerium acetate with molybdenum(VI) oxide (MoO3)...
For the determination of the precise lattice constants of Ti₂O₃, it is very important to use a Ti₂O₃...
DTFH61-85-C-00149The U.S. Accelerated Loading Facility (ALF), a full-scale accelerated pavement test...
During this experimental testing program the effects of the simultaneous application of high pressur...
Paper 1: “Surface electromagnetic wave (SEW) dispersion curves are usually calculated using a simple...
At present copper sulfide ores are recovered by pyrometallurgical processes. While the recovery of c...
Shell molds containing additions of ten to fifty percent magnetite, Fe3O4, of various particle sizes...
The flotation of sulphide minerals from siliceous and calcareous gangue minerals always gives a conc...
For many years, there has been talk expressing great concern about the oil reserves in the United St...
The effect of the area and type of surface of ten silica thickeners and aluminum oxide on grease per...
Presently, the theory is held that the total frog skin potential (P.D.) is generated within the epid...
The ability of silica to carry a load to within a few degrees of its melting point and its tolerance...
The vapor phase photolysis of benzoic acid has been investigated in a flow system at temperatures ra...
Not Available.J. Carter EaveyNot ListedNot ListedMaster of ArtsDepartment Not ListedCunningham Memor...
With the advent of legislation against pollution, and rising wage, manufacturing, and materials cost...
Reaction of aqueous solutions of either lanthanum or cerium acetate with molybdenum(VI) oxide (MoO3)...
For the determination of the precise lattice constants of Ti₂O₃, it is very important to use a Ti₂O₃...
DTFH61-85-C-00149The U.S. Accelerated Loading Facility (ALF), a full-scale accelerated pavement test...
During this experimental testing program the effects of the simultaneous application of high pressur...
Paper 1: “Surface electromagnetic wave (SEW) dispersion curves are usually calculated using a simple...