The aim of this work is studying the binary system ??'??? Ni?)with two ratios (y=36,80) by using casting method for preparing the samples.Magnetic and Mechanical properties have been studidt different httrea^nttem^rature.All the alloys were found a ferromagnetic behavior and sensitive to the heat treatment. Best properties were found at the heat treatment 1100 C°.A significant different results were found above 1100C° for lower magnetic and mechanical values. This is possibly due to the change on the degree of magnetic moment orders, in which most of the moments are started to remove from coupled ferromagnetically.
An investigation has been performed on the change of the Young\u27s modulus and the density of Ni-Mn...
AbstractThe effect of “in situ” thermal treatments (by DSC measurements) on the martensitic transfor...
Mechanical alloying was used to prepare $Co_{40}Fe_{60}$, $Co_{60}Fe_{35}Ni_{5}$, $Co_{40}Fe_{45}Ni_...
Pure nickel sheets of about 50 microns in thickness are cold rolled to varied degrees of reduction u...
The influence of heat-treatment on the magnetic properties of face-centered cubic nickel-cobalt allo...
Magnetic properties of nickel depend on the one hand of purity of metal and on the other hand of mec...
application/pdfThe ΔE effect has been measured by the method of magnetostrictive vibration with anne...
The effect of the cyclic heat-treatments on the martensitic transformation was examined with iron-ni...
Includes bibliographical references.Includes illustrations.The magnetic properties of a sintered sam...
The aim of this study is focused on the mechanical and the microstructural characterization of two N...
This study investigated the effects of adding a third alloying element, Ni, to create Fe70-xPd30Nix ...
The effect of heat treatments on the microstructure and mechanical properties of Ni base superalloys...
This paper reports on the effects of alloy composition and applied stress on the magnetic properties...
As-cast NiCuCrMoTiAlNb nickel-based alloys were subjected to two-stage heat treatment, including sol...
The crystal and magnetic properties of (Fe80Nb6B14)1−xNix (x = 0.1, 0.2 and 0.4) bulk alloys prepare...
An investigation has been performed on the change of the Young\u27s modulus and the density of Ni-Mn...
AbstractThe effect of “in situ” thermal treatments (by DSC measurements) on the martensitic transfor...
Mechanical alloying was used to prepare $Co_{40}Fe_{60}$, $Co_{60}Fe_{35}Ni_{5}$, $Co_{40}Fe_{45}Ni_...
Pure nickel sheets of about 50 microns in thickness are cold rolled to varied degrees of reduction u...
The influence of heat-treatment on the magnetic properties of face-centered cubic nickel-cobalt allo...
Magnetic properties of nickel depend on the one hand of purity of metal and on the other hand of mec...
application/pdfThe ΔE effect has been measured by the method of magnetostrictive vibration with anne...
The effect of the cyclic heat-treatments on the martensitic transformation was examined with iron-ni...
Includes bibliographical references.Includes illustrations.The magnetic properties of a sintered sam...
The aim of this study is focused on the mechanical and the microstructural characterization of two N...
This study investigated the effects of adding a third alloying element, Ni, to create Fe70-xPd30Nix ...
The effect of heat treatments on the microstructure and mechanical properties of Ni base superalloys...
This paper reports on the effects of alloy composition and applied stress on the magnetic properties...
As-cast NiCuCrMoTiAlNb nickel-based alloys were subjected to two-stage heat treatment, including sol...
The crystal and magnetic properties of (Fe80Nb6B14)1−xNix (x = 0.1, 0.2 and 0.4) bulk alloys prepare...
An investigation has been performed on the change of the Young\u27s modulus and the density of Ni-Mn...
AbstractThe effect of “in situ” thermal treatments (by DSC measurements) on the martensitic transfor...
Mechanical alloying was used to prepare $Co_{40}Fe_{60}$, $Co_{60}Fe_{35}Ni_{5}$, $Co_{40}Fe_{45}Ni_...