In this manuscript the results of experimental studies of the properties of composite materials based on lignocellulosic matrix (LC) filled with electrolytic copper powder and chemically obtained silver powder are presented. Volume fractions of metal fillers in the composite materials in tested samples were varied in the range of 1.6-30% (v/v), and the samples were prepared by compression - cold pressing. Characterization included examination of the influence of particle size and morphology on the conductivity and percolation threshold of the composites using variety of testing techniques: SEM, TGA, DSC, particle size distribution and conductivity measurements. Thermal analysis of the prepared composites showed the improvement of the therma...
It was shown that metallic chromium in aqueous solution of sulfuric acid dissolves in accord with th...
In the present study, the influence of different encapsulation techniques (lyophilization and spray ...
The first successful attempt to electrodeposit Zn-Mn alloy coatings from alkaline bath was made only...
Kompozitni materijali dobijaju sve veću industrijsku primenu u svetu.Kompoziti bazirani na polimerim...
Dental materials have specific requirements regarding behavior in exploitation conditions. Poly (met...
Ni/WC and Cu/WC composite coatings were obtained in two steps. The first step consists of the inert ...
Conditions for obtaining copper powder with different regimes of electrolysis [potentiostatic, galva...
The subject of the research is influence of sulfuric acid on morphology of electrochemically obtaine...
The effect different deposition regimes (constant and reversing currents), on the powdered copper el...
Goals. The goal of this study was a development of biocompatible composite hydrogels, structurally s...
The subject of this study is the quantitative adhesion of a UV-curing composite film based on Bis-GM...
Na osnovu izvršenih istraživanja ustanovljeno je da postoji međusobna povezanost mikrostrukture, meh...
Fokus ove doktorske disertacije je na pripremi i karakterizaciji magnetnihnanokompozitnih membrana z...
U ovom je radu ispitivan utjecaj pH tla i dodatka kompleksirajućeg agensa na sadržaj kadmija u pojed...
Elektrodepozicijom (ED) pod različitim procesnim uslovima (gustina struje, koncentracija tiouree, d...
It was shown that metallic chromium in aqueous solution of sulfuric acid dissolves in accord with th...
In the present study, the influence of different encapsulation techniques (lyophilization and spray ...
The first successful attempt to electrodeposit Zn-Mn alloy coatings from alkaline bath was made only...
Kompozitni materijali dobijaju sve veću industrijsku primenu u svetu.Kompoziti bazirani na polimerim...
Dental materials have specific requirements regarding behavior in exploitation conditions. Poly (met...
Ni/WC and Cu/WC composite coatings were obtained in two steps. The first step consists of the inert ...
Conditions for obtaining copper powder with different regimes of electrolysis [potentiostatic, galva...
The subject of the research is influence of sulfuric acid on morphology of electrochemically obtaine...
The effect different deposition regimes (constant and reversing currents), on the powdered copper el...
Goals. The goal of this study was a development of biocompatible composite hydrogels, structurally s...
The subject of this study is the quantitative adhesion of a UV-curing composite film based on Bis-GM...
Na osnovu izvršenih istraživanja ustanovljeno je da postoji međusobna povezanost mikrostrukture, meh...
Fokus ove doktorske disertacije je na pripremi i karakterizaciji magnetnihnanokompozitnih membrana z...
U ovom je radu ispitivan utjecaj pH tla i dodatka kompleksirajućeg agensa na sadržaj kadmija u pojed...
Elektrodepozicijom (ED) pod različitim procesnim uslovima (gustina struje, koncentracija tiouree, d...
It was shown that metallic chromium in aqueous solution of sulfuric acid dissolves in accord with th...
In the present study, the influence of different encapsulation techniques (lyophilization and spray ...
The first successful attempt to electrodeposit Zn-Mn alloy coatings from alkaline bath was made only...