Topics
DMAWork
Damping characteristics of 8090 Al alloy and its composites reinforced with 8, 12, and 18 vol pct SiC particles were investigated using a dynamic mechanical analyzer (DMA). Tests were done at different frequencies over a temperature range of $27^oC$ to $300^oC$. Composites show higher damping capacity than the unreinforced alloy. Damping capacity is found to increase with decreasing frequency. An equation relating damping capacity with frequency has been proposed. The damping data are analyzed in the light of matrix microstructure and different operative mechanisms
The use of metal matrix composites (MMC) has increased steadily in the last two decades. Conventiona...
Damping behavior of eutectoid zinc-aluminum composites was studied in the 25 to 330°C temperature ra...
The Ti6Al4V–SiCf composite, reinforced by unidirectional SiC fibres (SCS-6), has been investigated b...
Damping characteristics of 8090 Al alloy and its composites reinforced with 8, 12, and 18 vol pct Si...
Metallic materials known for their good toughness and ductility are now contemplated as replacements...
AbstractIn the present study, the damping behavior of hybrid composites has been investigated using ...
The low-frequency internal friction behavior of SiC particle reinforced Al matrix composites was stu...
The thermo-mechanical behavior of aluminum alloys reinforced with SiC particles was investigated by ...
In this study, electroceramics PBN and PLZT along with SiC were included in Al-3.96. wt.%. Mg (A514....
The structural characteristics, mechanical and damping properties of stir-cast Al-10 wt.% Zn based c...
Mechanical damping (in the longitudinal vibration mode only) and temperature dependence of dynamic m...
Dynamic modulus and damping capacity property data were measured from 20 to over 500 C for unidirect...
AbstractWith the advancement of composite technology, the selection of proper reinforcement in the m...
In this investigation, special consideration was given to observe the influence of the acquired ultr...
The damping capacity of cast graphitic aluminum alloy composites has been measured using a torsion p...
The use of metal matrix composites (MMC) has increased steadily in the last two decades. Conventiona...
Damping behavior of eutectoid zinc-aluminum composites was studied in the 25 to 330°C temperature ra...
The Ti6Al4V–SiCf composite, reinforced by unidirectional SiC fibres (SCS-6), has been investigated b...
Damping characteristics of 8090 Al alloy and its composites reinforced with 8, 12, and 18 vol pct Si...
Metallic materials known for their good toughness and ductility are now contemplated as replacements...
AbstractIn the present study, the damping behavior of hybrid composites has been investigated using ...
The low-frequency internal friction behavior of SiC particle reinforced Al matrix composites was stu...
The thermo-mechanical behavior of aluminum alloys reinforced with SiC particles was investigated by ...
In this study, electroceramics PBN and PLZT along with SiC were included in Al-3.96. wt.%. Mg (A514....
The structural characteristics, mechanical and damping properties of stir-cast Al-10 wt.% Zn based c...
Mechanical damping (in the longitudinal vibration mode only) and temperature dependence of dynamic m...
Dynamic modulus and damping capacity property data were measured from 20 to over 500 C for unidirect...
AbstractWith the advancement of composite technology, the selection of proper reinforcement in the m...
In this investigation, special consideration was given to observe the influence of the acquired ultr...
The damping capacity of cast graphitic aluminum alloy composites has been measured using a torsion p...
The use of metal matrix composites (MMC) has increased steadily in the last two decades. Conventiona...
Damping behavior of eutectoid zinc-aluminum composites was studied in the 25 to 330°C temperature ra...
The Ti6Al4V–SiCf composite, reinforced by unidirectional SiC fibres (SCS-6), has been investigated b...
Add to ORKG