The superplastic properties of a cold-rolled Al±6Mg±0.3Sc alloy were studied at temperatures between 450 and 5608C and strain rates between 10⁻⁴ and 100⁰ s⁻¹. The alloy was observed to exhibit super- plasticity over wide temperature (475±5208C). It was found that the addition of Sc to Al±Mg alloys resulted in a uniform distribution of fine coherent Al₃Sc precipitates which effectively pinned subgrain and grain boundaries during static and dynamic recrystallization. In this paper, the microstructural evolution during superplastic deformation was systematically examined using both opti- cal and transmission electron microscopyyesBelgorod State Universit
yesIt was shown that an Al–5.7%Mg-0.32%Sc-0.3%Mn alloy subjected to severe plastic deformation throu...
An Al-3% Mg-0.2% Sc alloy was fabricated by casting and subjected to severe plastic deformation thro...
This paper describes grain refinement of an Al-3%Mg-0.2%Sc alloy using the equal-channel angular pre...
yesThe superplastic properties of a cold-rolled Al±6Mg±0.3Sc alloy were studied at temperatures betw...
We have characterized in the Al-Mg system the microstructure and mechanical properties of a cold-rol...
An Al-3 pct Mg-0.2 pct Sc alloy was fabricated by casting and subjected to equal-channel angular pre...
An Al-6%Mg -0.3%Sc-0.3%Mn alloy was subjected to equal-channel angular extrusion (ECAE) at 325⁰C to ...
The application of severe plastic deformation to metallic alloys via the procedure of equal-channel ...
In this paper we concentrate on the superplastic behavior and the microstructural evolution of two c...
It was shown that an Al–5.7%Mg-0.32%Sc-0.3%Mn alloy subjected to severe plastic deformation through ...
In this paper we concentrate on the superplastic behavior and the microstructural evolution of two c...
Recent studies have shown that a suitably thermomechanically processed Al-Zn-Mg-Cu-Zr-Sc alloy havin...
This paper concentrates on the superplastic response of fine-grained and coarse-grained Al–Mg alloys...
The boundary misorientations in an Al-1OMg-O.1Zr (wt%) alloy, thermomechanically processed by rollin...
This paper concentrates on the superplastic response of fine-grained and coarse-grained Al-Mg alloys...
yesIt was shown that an Al–5.7%Mg-0.32%Sc-0.3%Mn alloy subjected to severe plastic deformation throu...
An Al-3% Mg-0.2% Sc alloy was fabricated by casting and subjected to severe plastic deformation thro...
This paper describes grain refinement of an Al-3%Mg-0.2%Sc alloy using the equal-channel angular pre...
yesThe superplastic properties of a cold-rolled Al±6Mg±0.3Sc alloy were studied at temperatures betw...
We have characterized in the Al-Mg system the microstructure and mechanical properties of a cold-rol...
An Al-3 pct Mg-0.2 pct Sc alloy was fabricated by casting and subjected to equal-channel angular pre...
An Al-6%Mg -0.3%Sc-0.3%Mn alloy was subjected to equal-channel angular extrusion (ECAE) at 325⁰C to ...
The application of severe plastic deformation to metallic alloys via the procedure of equal-channel ...
In this paper we concentrate on the superplastic behavior and the microstructural evolution of two c...
It was shown that an Al–5.7%Mg-0.32%Sc-0.3%Mn alloy subjected to severe plastic deformation through ...
In this paper we concentrate on the superplastic behavior and the microstructural evolution of two c...
Recent studies have shown that a suitably thermomechanically processed Al-Zn-Mg-Cu-Zr-Sc alloy havin...
This paper concentrates on the superplastic response of fine-grained and coarse-grained Al–Mg alloys...
The boundary misorientations in an Al-1OMg-O.1Zr (wt%) alloy, thermomechanically processed by rollin...
This paper concentrates on the superplastic response of fine-grained and coarse-grained Al-Mg alloys...
yesIt was shown that an Al–5.7%Mg-0.32%Sc-0.3%Mn alloy subjected to severe plastic deformation throu...
An Al-3% Mg-0.2% Sc alloy was fabricated by casting and subjected to severe plastic deformation thro...
This paper describes grain refinement of an Al-3%Mg-0.2%Sc alloy using the equal-channel angular pre...