Ta2O5 films were deposited using the conventional electron beam evaporation method and then annealed at temperatures in the range 373-673 K. Chemical composition, scattering and absorption were examined by X-ray photoelectron spectroscopy (XPS), total integrated scattering (TIS) measurement and the surface thermal lensing (m) technique, respectively. The laser-induced damage threshold (LIDT) was assessed using the output from an Nd:YAG laser with a pulse length of 12 ns. The results showed that the improvement of the LIDT after annealing was due to the reduced substoichiometric and structural defects present in the film. The LIDT increased slightly below 573K and then increased significantly with increase in annealing temperature, which cou...
Reactively evaporated thin films of tantalum oxide are prepared on glass substrate, using electron ...
We investigate the effect of post-deposition annealing (for temperatures from 848 K to 1273 K) on th...
We investigate the effect of post-deposition annealing (for temperatures from 848 K to 1273 K) on th...
Ta2O5 films are prepared on Si, BK7, fused silica, antireflection (AR) and high reflector (HR) subst...
Ta2O5 films were deposited by conventional electron beam evaporation method and then annealed in air...
Ta2O5 films are deposited on fused silica substrates by conventional electron beam evaporation metho...
Ta2O5 films deposited by ion beam sputtering were post-treated with different methods. The optical p...
Ta2O5 films were prepared by electron beam evaporation under different oxygen partial pressures. Thr...
High laser-induced damage threshold (LIDT)Ta2O5 films were prepared by the sol-gel method using TaCl...
Optical coatings deposited by the dual ion beam sputtering (DIBS) method usually show high compressi...
Optical coatings deposited by the dual ion beam sputtering (DIBS) method usually show high compressi...
A series or Ta2O5 films with different SiO2 additional layers including overcoat, undercoat and inte...
Tantalum oxide (TaOx) films were deposited by KrF excimer laser ablation of Ta2O5 targets in an oxyg...
Ta2O5膜采用传统的电子束蒸发方法制备,并在氧气中673 K的条件下进行了退火12 h处理。首先在1-on-1体系下对Ta2O5膜进行了532和1064 nm波长下的激光损伤阈值(LIDT) 研究,...
Tantalum pentoxide (Ta2O5) thin films (20-50 nm) have been grown by 1064 nm Nd:YAG laser oxidation o...
Reactively evaporated thin films of tantalum oxide are prepared on glass substrate, using electron ...
We investigate the effect of post-deposition annealing (for temperatures from 848 K to 1273 K) on th...
We investigate the effect of post-deposition annealing (for temperatures from 848 K to 1273 K) on th...
Ta2O5 films are prepared on Si, BK7, fused silica, antireflection (AR) and high reflector (HR) subst...
Ta2O5 films were deposited by conventional electron beam evaporation method and then annealed in air...
Ta2O5 films are deposited on fused silica substrates by conventional electron beam evaporation metho...
Ta2O5 films deposited by ion beam sputtering were post-treated with different methods. The optical p...
Ta2O5 films were prepared by electron beam evaporation under different oxygen partial pressures. Thr...
High laser-induced damage threshold (LIDT)Ta2O5 films were prepared by the sol-gel method using TaCl...
Optical coatings deposited by the dual ion beam sputtering (DIBS) method usually show high compressi...
Optical coatings deposited by the dual ion beam sputtering (DIBS) method usually show high compressi...
A series or Ta2O5 films with different SiO2 additional layers including overcoat, undercoat and inte...
Tantalum oxide (TaOx) films were deposited by KrF excimer laser ablation of Ta2O5 targets in an oxyg...
Ta2O5膜采用传统的电子束蒸发方法制备,并在氧气中673 K的条件下进行了退火12 h处理。首先在1-on-1体系下对Ta2O5膜进行了532和1064 nm波长下的激光损伤阈值(LIDT) 研究,...
Tantalum pentoxide (Ta2O5) thin films (20-50 nm) have been grown by 1064 nm Nd:YAG laser oxidation o...
Reactively evaporated thin films of tantalum oxide are prepared on glass substrate, using electron ...
We investigate the effect of post-deposition annealing (for temperatures from 848 K to 1273 K) on th...
We investigate the effect of post-deposition annealing (for temperatures from 848 K to 1273 K) on th...