The objective of this study is to investigate the effect of sintering temperature on the synthesis of SiC produced from rice husk ash (RHA) and 2B graphite pencils. The SiC was synthesized by using solid state reaction method sintered at temperatures of 750°C, 1000°C and 1200°C for 26 hours, 11.5 hours and 11.5 hours, respectively. The quantity and crystallinity level of SiC phase were measured by means of Rigaku MiniFlexII X-Ray Diffraction (XRD). The microstructure of SiC was examined by using Tescan Vega3SB Scanning Electron Microscopy (SEM). The XRD results showed that the concentration (wt%) of SiC phase increases with the increasing of sintering temperature. SEM results showed that the crystallinity level of SiC crystal is improving a...
Pine (Pinus silvestris) wood samples were dried and impregnated with a SiO2 sol from a sol–gel proce...
Microstructure development and phase formation processes during sintering of silicon carbide based m...
Attempts have been made to describe the influence of sintering temperature on the microstructure and...
The introduction of sintering aids into silicon carbide powder system is a critical step in the deve...
Synthesis of Silicon Carbide (SiC) has been performed using a solid-state reaction method. We used ...
Porous silicon carbide (SiC) is a promising ceramic for high-temperature applications due to its uni...
Coprecipitation was examined as a method of introducing sintering aids into silicon carbide (SiC) as...
In past decades design of experiments and simulation analysis have been recognised as powerful tools...
Silica ceramics were prepared using three types of raw materials derived from rice husk. Cleaned hus...
Different LPS-SiC were produced by pressureless sintering in argon atmosphere, starting from differ...
The feasibility of flash sintering a covalent ceramic, SiC, has been investigated for the first time...
This paper presents the results of the entropy calculation of the equilibrium constants of chemical ...
Silicon carbide based materials are being increasingly used as a room temperature structural materia...
Silicon carbide (SiC) and SiC-C composite are non-oxide materials with good thermal properties so th...
The stable slurry was prepared by ball-milling with a certain proportion of silica fume as silicon s...
Pine (Pinus silvestris) wood samples were dried and impregnated with a SiO2 sol from a sol–gel proce...
Microstructure development and phase formation processes during sintering of silicon carbide based m...
Attempts have been made to describe the influence of sintering temperature on the microstructure and...
The introduction of sintering aids into silicon carbide powder system is a critical step in the deve...
Synthesis of Silicon Carbide (SiC) has been performed using a solid-state reaction method. We used ...
Porous silicon carbide (SiC) is a promising ceramic for high-temperature applications due to its uni...
Coprecipitation was examined as a method of introducing sintering aids into silicon carbide (SiC) as...
In past decades design of experiments and simulation analysis have been recognised as powerful tools...
Silica ceramics were prepared using three types of raw materials derived from rice husk. Cleaned hus...
Different LPS-SiC were produced by pressureless sintering in argon atmosphere, starting from differ...
The feasibility of flash sintering a covalent ceramic, SiC, has been investigated for the first time...
This paper presents the results of the entropy calculation of the equilibrium constants of chemical ...
Silicon carbide based materials are being increasingly used as a room temperature structural materia...
Silicon carbide (SiC) and SiC-C composite are non-oxide materials with good thermal properties so th...
The stable slurry was prepared by ball-milling with a certain proportion of silica fume as silicon s...
Pine (Pinus silvestris) wood samples were dried and impregnated with a SiO2 sol from a sol–gel proce...
Microstructure development and phase formation processes during sintering of silicon carbide based m...
Attempts have been made to describe the influence of sintering temperature on the microstructure and...